Ls Water Pump Torque

By Bintang 10 Feb, 2019

I was browsing this forum a while ago and stumbled upon a tread or link to a bunch of torque. Be the first to write a review

Pin on 67 Nova

Answer id 5191 | published 03/22/2019 02:03.

Ls water pump torque. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. What are the torque specs for a aluminum water pump on a 2004 chevy silverado 6.0 they need to be done in 2 stages the pass needs to be set on 11 ft.lbs. However there is more adaptation for the water pumps with our water pump spacers.

Information sources are courtesy of helms manuals, mallett cars, ltd., chevy ls1/ls6 performance by chris endres & hp books, chevy ls1/ls6 v8s by will handzel and cartech, chevrolet owners & operators manuals and my own data. The new small block is known as the ls engine family and has more than successfully replaced 350's and 305's that were based in design from the 1950's. By solo z in forum general help replies:

Oil pump screen nuts : Clean the gasket mounting surfaces. $49.99 ) (no reviews yet) write a.

If a gasket is supplied with the replacement part, it should be used. The ls water pump spacers from lsx innovations will allow you to use a car water pump with the truck accessories, spacing the car water pump out to align with everything else. Water pump pulley bolts (final pass) / 18 this data is presented for convienience only.

The specs listed are for stock fasteners. For a total of 33 ft.lbs. Email me at 607331914@pm.me which original lextreme parts you need and i'll check availability.

You can not use any water pump on any ls based engine. Positive crankcase ventilation (pcv) system strap nut (at right front vapor vent pipe stud) 106 lb in Note the water pumps on some of the engines covered may have been installed using sealer only, no gasket, at the factory.

Yes, i have looked over at ls1howto.com, and all the torque specs are for a 2000 f body car which has a aluminum block. November 24, 2020 a limited supply of original lextreme parts back in stock including egr delete kits, torque converters, supercharger brackets, etc! Answer id 5190 | published 03/22/2019 01:44.

If you use arp fasteners, follow the instructions that came with your new hardware. Oil pump cover bolts : I'm looking for torque specs on the water pump fig.

Click on one of the links below. Plus i know there is a difference in specs for 1st and 2nd design connecting rods. Fasteners that list an angle are torque to yield (tty).

Over 6,000 automotive torque specs. This is a discussion on torque spec sheet within the camaro / ss forums, part of the vehicle specific category; Over 6,000 automotive torque specs.

Then the second pass needs to be set on 22 ft.lbs. We use cookies to give you the best possible experience on our website. Oil pump relief valve plug :

Search car torque specifications by engine or model. Our ls water pump spacers are perfect for running a chevy camaro ls1 water pump and intake manifold with your factory lq4, lq9, 6.0, 5.3, 4.8 or any truck accessory drive. Thermostat housing to water pump retaining bolt 15y 11lbft water pump to engine block retaining bolt • first pass 15y 11lbft • second pass 30y 22lbft document id:

1996 lt1 corvette engine parts. G general spacing applies for the water pumps as well. Ls electric water pump adapter plates (converts bbc pump to ls engine) ict billet 551515 ict billet.

Oil pump cover to oil pump retaining bolt 12y 106lbin oil pressure relief valve plug to oil pump 14y 124lbin oil pump screen to crankshaft oil deflector retaining nut. Fasteners that list an angle are torque to yield (tty). Putting stage 2.5 prc heads and a cam in my 6.0, was wondering if anyone had torque specs for everything.

Yes they will bolt up, but spacing is very important, same as pulley size, ect. Replacing the old tried and true small block chevy engine with a new version would not be an easy task. Ls billet aluminum rear main cover engine seal housing ls1 ls3 ls7.

The specs listed are for stock fasteners. Torque specs for ls1 motors. If you use arp fasteners, follow the instructions that came with your new hardware.

Please note that the sc400 turbo kit is all sold out and won't return. Ls lt torque plate engine block machining boring honing cylinder motor 4.05 ict. The ls1 camaro water pump has a much more desirable water outlet location than the factory truck water pump, and these spacers allow the use of the ls1 camaro water pump on.

I just want to make sure i have the exact specs for my iron block 6.0. Search car torque specifications by engine or model.

Pin on Ls engine